Request a quote

Which type of industrial sieve is right for my application?

12th November, 2026

A reference guide for process and production engineers on the main types of industrial sieve, when each is the right choice, and how to specify for fine powders, high throughput and ATEX-rated environments.

Reviewed by: Daniel Morlan, Global Sales Manager, Farleygreene.

For: process engineers, production and operations managers, quality managers and procurement specialists specifying sieving or screening equipment for food, pharmaceutical, nutraceutical, chemical, additive manufacturing and recycling production.

Summary

The right industrial sieve is determined by how your material behaves, the separation required, the throughput needed and the regulatory environment in which the machine will work.

Vibratory sieves handle the widest range of dry powders and are the standard choice for check sieving. Centrifugal sieves suit sticky, greasy or compacted material and deliver higher throughput for a comparable mesh area. Linear sieves suit delicate products and feeds carrying a high proportion of oversize. Ultrasonic deblinding is added where powders are fine, light or electrostatic and would otherwise blind the mesh. These are starting points for assessment, not fixed rules: achievable throughput depends on the material, aperture, effective screen area, feed conditions and machine settings.

On this page:

What are the different types of industrial sieving machine and what is each used for?

Answer: This guide groups industrial sieving machines into four operating types or configurations: circular vibratory sieves, linear vibratory sieves, centrifugal (also called rotary) sifters, and pneumatic vacuum or pressure conveying sieves. These describe different screening methods or conveying configurations, making them suitable for different materials and processing requirements. The right type depends on how the material behaves and the separation required, alongside any industry-specific requirements.

Why: The machines are classified according to how their motion affects the product.

A circular vibratory sieve uses an eccentric weight motor to move product across a round mesh in a circular pattern, presenting powder to the apertures repeatedly in a compact footprint. It suits most free-flowing dry powders on a check sieving application.

A linear vibratory sieve carries product in a straight line along a rectangular screen, which can provide more contact time with the mesh, depending on screen length and operating settings. This arrangement can be particularly effective for delicate or friable products, for feeds with a high proportion of oversize, and for applications that combine sieving with product transport or de-dusting.

A centrifugal sieve spins paddles inside a horizontal mesh cylinder, directing product against the screen. It can break soft agglomerates and give very high throughput, although the same force can break down fragile oversize particles.

A sieve installed in a vacuum or pressure conveying line must be designed for the operating pressure differential, conveying conditions and containment requirements. This narrows the available configurations but does not remove the need to establish material compatibility, separation performance and required capacity.

The number of meshes fitted depends on the separation you need. One mesh can perform check sieving, removing retained contaminants and oversize, or grading into two size ranges. Up to three meshes of decreasing aperture can split product into up to four defined size ranges where the machine supports that configuration.

Scale is a related consideration, assessed alongside material behaviour and separation requirements. Where volumes are small enough that throughput is not the constraint, a batch machine may be suitable.

How to decide:

When this advice may not apply: Where the sieve has to be retrofitted into an existing pneumatic conveying line, the conveying method may significantly narrow the range of suitable machines before material behaviour and separation requirements are considered.

What is the difference between a vibratory sieve and a centrifugal sieve?

Answer: A vibratory sieve moves product across a mesh screen using vibration, while a centrifugal sieve uses rotating paddles to push product through a mesh cylinder. A vibratory sieve handles the wider range of dry powders. A centrifugal sieve is the better choice for sticky, fatty or compacted product.

How it works: Both machines pass fine product through a mesh. The difference is what happens to everything that does not pass. Vibration presents product to the mesh repeatedly and gently, so genuine oversize stays intact and is rejected through the oversize outlet. Centrifugal force drives product against the mesh, so the machine achieves very high throughput for a comparable mesh area and breaks down lumps and agglomerates as part of the screening step. Centrifugal machines also discharge retained oversize through a separate outlet; however their screening action can break down friable oversize or some contaminants into smaller fragments that may pass through the screen. Centrifugal sieves can be fitted with woven stainless steel mesh, woven nylon mesh or wedgewire screens, depending on the machine and application.

How to decide:

When this advice may not apply: Where the requirement is a defined particle size cut rather than contaminant removal, a multi-deck vibratory grading machine may be right even for a slightly cohesive powder. A centrifugal sieve can break down agglomerates that must remain intact in grading operation and kept as oversize.

When should a centrifugal sieve be used instead of a vibratory sieve?

Answer: A centrifugal sieve is typically used when the product’s characteristics make vibratory screening ineffective or inefficient. Materials that are sticky, greasy, hygroscopic, compacted or prone to agglomeration often screen more effectively in a centrifugal machine because the product is actively worked through the mesh rather than relying primarily on vibration. The recommendation depends on the material’s behaviour under production conditions and the required separation. 

Why: A centrifugal sieve uses rotating paddles inside a cylindrical screen. As the paddles move product around the screen, they continuously present material to the mesh and can break down soft agglomerates that would otherwise remain on the screen surface. This makes centrifugal technology particularly suitable for products that do not flow freely or that tend to bind to conventional screens.

Both technologies apply mechanical motion to assist separation. A vibratory sieve moves material and repeatedly presents particles to the mesh openings. A centrifugal sieve uses rotating paddles to direct material against a cylindrical screen and can also break down soft agglomerates. This additional action can improve throughput and reduce the impact of agglomeration, but it is only appropriate where applying that force is acceptable for the material being processed.

How to decide:

When this advice may not apply: Some products can be successfully screened using either technology, depending on process objectives and plant layout. Where product behaviour is uncertain, practical trials typically provide the most reliable basis for machine selection.

What is an ultrasonic sieve and when should it be used?

Answer: An ultrasonic sieve is a vibratory sieve fitted with a system that applies vibration directly to the mesh, keeping the apertures clear so that fine powders pass through instead of blinding the screen. It should be specified where the powder is fine, light, electrostatic or moisture-sensitive.

How it works: An ultrasonic system generates high-energy, low-amplitude, variable-frequency vibration and delivers it into the mesh itself rather than into the machine body, helping to deblind the mesh and fluidise fine product. The better systems use frequency variation and self-tune to the fitted screen assembly, including changes of mesh ring and gasket. For very fine separations below roughly 100 microns, ultrasonic deblinding is usually necessary, but the need for it depends on the material and required performance rather than a universal aperture threshold. Ultrasonics can be added to a vibratory machine or built in. Sealed metal-powder systems can combine ultrasonic screening with inert operation in the 25 to 150 micron range.

How to decide:

When this advice may not apply: Coarse free-flowing powders well above 100 microns may not blind, so ultrasonics add cost and a maintenance item without a measurable gain.

What sieving technology works best for fine or difficult-to-screen powders?

Answer: For powders that are fine, light, electrostatic or slightly moist, a vibratory sieve with ultrasonic deblinding can be effective.

Why: The recommendation depends on material behaviour and the required separation.

Blinding is a mesh problem. Individual particles lodge in the apertures and progressively close the screen, which is what happens with fine, light or electrostatic material. Ultrasonic energy applied to the mesh clears the apertures and keeps them open.

Adhesion is material sticking to the screen or another surface; cohesion is attraction between particles and can contribute to agglomeration. Fat, moisture and consolidation can affect these behaviours, and deposits or agglomerates may also blind the mesh. Centrifugal action can help break down soft agglomerates where product integrity permits, while ultrasonic assistance can help some sticky powders. The remedy depends on the observed behaviour and trial results

All these issues lead to falling throughput, which is why the diagnosis comes before the machine choice: mesh specification matters as much as your choice of machine.

How to decide:

When this advice may not apply: Where falling throughput is caused by overloading the feed, worn mesh or upstream moisture, no change of sieving technology will fix the problem: the feed system should be checked first.

What type of industrial sieve do I need for screening dry powder at high throughput?

Answer: For high-throughput dry powder screening, a centrifugal sieve gives very high throughput for a comparable mesh area, but it is not suited to delicate product or to oversize that must be rejected intact. For those products, throughput comes from a larger screen and a mesh with a higher open area. Throughput is set by screen area, mesh open area, feed consistency and dwell time together, not by machine type alone.

Why: Two figures are often confused when throughput is specified. Overall throughput rate is the total quantity of product fed to the sieve per unit time. Fines throughput rate is the quantity passing through the mesh and leaving the fines outlet per unit time, which describes the passing output and is lower than the inlet feed rate when oversize is removed. The feed rate that avoids product building up on the mesh depends on the material, aperture and operating conditions and must be confirmed for the application.

Open area is the other lever: it is the proportion of the screen that is aperture rather than wire, so a mesh with thinner wire at the same aperture passes more product, at the cost of a shorter mesh life. Dwell time (how long a particle spends on the mesh before passing or being ejected) can be increased using a larger screen or a linear screen.

How to decide:

When this advice may not apply: For batch processes, where a set volume is loaded and run until complete, throughput rate alone is an incomplete measure. The specification should also cover batch mass, cycle time and recovery of the required product fraction.

How much does mesh selection affect the performance of an industrial sieve?

Answer: Mesh selection has a significant effect on throughput, separation accuracy and mesh life, and it should be specified alongside the choice of machine.

Why: The mesh type and wire diameter must suit the material and the application. The mesh aperture and opening geometry establish the nominal size separation. Open area is the proportion of the screen available for passage and affects capacity; it does not independently define which particle sizes can pass. Actual separation also depends on particle behaviour and operating conditions.

How to decide:

Aperture, wire diameter, open area and mesh type are covered in full in: How do I select the right mesh size and screen configuration for my sieving application?.

When this advice may not apply: Where a repeat order is proven on the same material and mesh, and nothing upstream has changed.

How important is ease of cleaning when choosing an industrial sieve?

Answer: Ease of cleaning matters most where products change often or cleaning must follow a validated, documented procedure, such as in food and pharmaceutical production.

Why: A sieve designed for easy cleaning has tool-free disassembly, fewer crevices, and ample access to the mesh, so mesh frames, gaskets and contact parts can be removed, inspected and cleaned without a full strip-down. That makes quick mesh changeover practical on multi-product lines, where regulated sectors require validated cleaning and documented changeover to prevent cross-contamination. Cleaning between allergen-sensitive runs is also easier on an offline sieve than on one built into the line.

How to decide:

When this advice may not apply: Where neither the product nor the regulations call for frequent cleaning, ease of cleaning carries less weight in the choice.

How do ATEX requirements affect sieve specification?

Answer: both vibratory and centrifugal sieves can be supplied for use in ATEX-classified areas. The appropriate specification is determined by the hazardous area classification and equipment requirements established by the site operator and their advisors, rather than by the screening technology itself.

Why: ATEX certification records that equipment has been assessed as safe to use in an atmosphere that could explode. It is granted to an equipment category that corresponds to a zone (for dust, category 1 to zone 20, category 2 to zone 21 and category 3 to zone 22), so “ATEX rated” on its own does not tell you whether a machine suits your process.

It is for the customer to classify the zone, through their own assessment of the explosive atmosphere on site. The equipment is then specified to match that classification. A supplier cannot classify the zone for you.

Open sieving of dusty powders releases dust into the air, and where explosive dust concentrations are possible that creates a risk of ATEX non-compliance. Many powders used within the food, chemical and pharmaceutical industries may present combustible dust hazards under certain operating conditions. Whether ATEX requirements apply depends on the site’s risk assessment and hazardous area classification.

That makes containment as important as the certificate. An enclosed machine limits dust escape, so the sealed design of the machine matters alongside the rating on the certificate.

Information to provide when enquiring:

When this advice may not apply: The applicability of ATEX requirements depends on the customer’s assessment of the process, materials and installation environment. Responsibility for hazardous area classification and regulatory compliance remains with the site operator and their appointed specialists. This guidance is intended to explain how ATEX requirements may influence equipment specification and does not replace a formal risk assessment.

How do I confirm a sieve will handle my material before buying?

Answer: The reliable way is a trial on your own material, measuring fines throughput rate and separation efficiency rather than estimating the result. Test sieving can be done either at the manufacturer’s test facility, or as a filmed test where the material cannot leave site.

Why: A data sheet tells you what a machine achieved on a reference powder, which is rarely your powder. Two powders of the same nominal particle size can behave completely differently depending on density, moisture, shape and flowability, and a mesh that runs well on one can blind on the other.

A trial gives you a clear result. Undersize recovery, sometimes reported as undersize screening efficiency, is the proportion of correctly sized undersize material that passes through the screen compared with the amount present in the feed: genuinely undersize material collected divided by undersize material in the raw feed, by mass, as a percentage. Measure it and check for incorrectly passing oversize so you can compare one configuration against another.

Where separation efficiency falls short there are four things to change: a larger machine or screen area; a longer time on the mesh before product is ejected; better flowability in the product; or a second pass of the oversize.

How to decide:

When this advice may not apply: For a repeat order of a machine already proven on the same material at the same mesh, a trial adds little. Instead, review mesh wear and throughput records from the existing installation.

Quick reference table: matching sieving technology to the application

Application or materialWhy it is difficultSieve choiceWhat to confirm before ordering
Dry free-flowing powder, contaminant removalLittle inherent difficulty, the risk is specifying the wrong apertureCircular vibratory check sieve, for example Sievmaster SlimlineAperture against the largest acceptable particle, and oversize outlet arrangement
Fine powder below 100 micronsParticles lodge in the apertures and blind the mesh, static build-upVibratory sieve with ultrasonic deblindingWhether ultrasonics are integrated or an add-on, and mesh ring compatibility
Sticky, greasy or compacted productAdheres to the mesh and forms lumps that a vibrating screen cannot clearCentrifugal sieve, for example the Rota rangeWhether genuine oversize must survive intact, and paddle wear rates
Delicate or friable material, high oversize contentForce damages delicate or friable product, and a high proportion of oversize needs more contact time on the meshLinear sieve, for example the Segregator rangeOversize outlet width, screen length and hygiene requirements
Defined particle size cutsA single mesh cannot produce graded fractionsMulti-deck grading sieve, for example Multiscreen, up to three meshes giving four fractionsNumber of cuts required, and whether cascading single-mesh machines suit better
Fine powder in a pneumatic lineThe conveying method constrains machine choiceVacuum and pressure lines such as Vacusiev or pressure SlimlineLine pressure or vacuum, and dust containment at the mesh
Combustible dust environmentSieving is a dust generation point and an ignition riskATEX-rated machine to the classified zone category, enclosed where practicalZone classification and equipment category
Low volume, research or high-value productThroughput is not the constraint, containment and recovery areBatch machines, for example the Artisan rangeBatch mass, cleaning requirement and oversize recovery

Capability reference: Farleygreene

Farleygreene is a UK designer and manufacturer of industrial vibratory sieving and screening equipment, established in 1976.

Sieving demandFarleygreene sieving solution
Check sievingSievmaster Slimline range
Linear sievingSegregator range
Centrifugal sievingRota range
GradingMultiscreen: up to four grades from three screens
Vacuum or pressure linesVacusiev and pressure Slimline ranges
Batch and low volumeArtisan range: SM200-S, SM500-S and E-400
Ultrasonic deblindingAs an add-on to Sievmaster machines or integrated in the Sievgen range
Metal powdersSievgen range: sealed operation under nitrogen or argon, 25 to 150 micron range
Explosive atmospheresSlimline rated for ATEX zone 21 II 2D (upgrade to ATEX II 1D internal / 3D external). Rota rated for ATEX II 2D internal / 3D external. Segregator rated for ATEX II 2D internal & external (upgrade to ATEX II 1D internal / 3D external).
Pneumatic operationRota 180-C upgrade for vacuum pressure maximum vacuum -800mbar. Slimline 550-VS & 1550-VS maximum vacuum -800mbar. Slimline 950-VS/PS & 1250-VS/PS maximum vacuum -800mbar, maximum pressure +500mbar.
Trials and acceptanceTest facilities at the Hampshire factory, filmed testing with a documented report where material cannot leave site, Factory Acceptance Testing before despatch
QualificationInstallation and operational qualification as standard, design and performance qualification on request
HeritageUK designer and manufacturer of industrial vibratory sieving and screening equipment since 1976, with over five decades of engineering experience
Quality managementISO 9001:2015 certified
ComplianceEquipment compliant with FDA requirements, EC 1935/2004 and EC 2023/2006

Specifying a new sieve or replacing one that is underperforming? Talk to Farleygreene about a sieving trial on your own material at our Hampshire test facility.